? semiconductor components industries, llc, 2000 may, 2000 rev. 4 1 publication order number: mcr703a/d
preferred device
reverse blocking thyristors pnpn devices designed for high volume, low cost consumer applications such as temperature, light and speed control; process and remote control; and warning systems where reliability of operation is critical. ? small size ? passivated die surface for reliability and uniformity ? low level triggering and holding characteristics ? recommend electrical replacement for c106 ? surface mount package e case 369a ? device marking: device type, e.g., for mcr703a: cr703a, date code maximum ratings (t j = 25 c unless otherwise noted) rating symbol value unit peak repetitive offstate voltage (1) (t c = 40 to +110 c, sine wave, 50 to 60 hz, gate open) mcr703a mcr704a mcr706a mcr708a v drm, v rrm 100 200 400 600 volts peak non-repetitive offstate voltage (sine wave, 50 to 60 hz, gate open, t c = 40 to +110 c) mcr703a mcr704a mcr706a mcr708a v rsm 150 250 450 650 volts onstate rms current (180 conduction angles, t c = 90 c) i t(rms) 4.0 amps average onstate current (180 conduction angles) t c = 40 to +90 c t c = +100 c i t(av) 2.6 1.6 amps non-repetitive surge current (1/2 sine wave, 60 hz, t j = 110 c) (1/2 sine wave, 1.5 ms, t j = 110 c) i tsm 25 35 amps circuit fusing (t = 8.3 ms) i 2 t 2.6 a 2 s forward peak gate power (pulse width 10 s, t c = 90 c) p gm 0.5 watt forward average gate power (t = 8.3 ms, t c = 90 c) p g(av) 0.1 watt forward peak gate current (pulse width 10 s, t c = 90 c) i gm 0.2 amp operating junction temperature range t j 40 to +110 c storage temperature range t stg 40 to +150 c (1) v drm and v rrm for all types can be applied on a continuous basis. ratings apply for zero or negative gate voltage; however, positive gate voltage shall not be applied concurrent with negative potential on the anode. blocking voltages shall not be tested with a constant current source such that the voltage ratings of the devices are exceeded. scrs 4.0 amperes rms 100 thru 600 volts device package shipping ordering information mcr703at4 dpak 369a 16mm tape and reel (2.5k/reel) http://onsemi.com k g a mcr704at4 dpak 369a 16mm tape and reel (2.5k/reel) dpak case 369a style 5 1 2 3 4 pin assignment 1 2 3 anode cathode gate 4 anode preferred devices are recommended choices for future use and best overall value. mcr706at4 dpak 369a 16mm tape and reel (2.5k/reel) mcr708at4 dpak 369a 16mm tape and reel (2.5k/reel)
mcr703a series http://onsemi.com 2 thermal characteristics characteristic symbol max unit thermal resistance, junction to case r q jc 8.33 c/w thermal resistance, junction to ambient (1) r q ja 80 c/w maximum lead temperature for soldering purposes 1/8 from case for 10 seconds t l 260 c electrical characteristics (t c = 25 c unless otherwise noted.) characteristic symbol min typ max unit off characteristics peak repetitive forward or reverse blocking current (v ak = rated v drm or v rrm ; r gk = 1 k w )t c = 25 c t c = 110 c i drm , i rrm e e e e 10 200 m a on characteristics peak forward aono voltage (i tm = 8.2 a peak, pulse width = 1 to 2 ms, 2% duty cycle) v tm e e 2.2 volts gate tri gger current (continuous dc) (2) (v ak = 12 vdc, r l = 24 ohms) t c = 25 c t c = 40 c i gt e e 25 e 75 300 m a gate tri gger v oltage (continuous dc) (2) t c = 25 c (v ak = 12 vdc, r l = 24 ohms) t c = 40 c v gt e e e e 0.8 1.0 volts gate non-tri gger v oltage (2) (v ak = 12 vdc, r l = 100 ohms, t c = 110 c) v gd 0.2 e e volts holding current (v ak = 12 vdc, gate open) t c = 25 c (initiating current = 200 ma) t c = 40 c i h e e e e 5.0 10 ma peak reverse gate blocking voltage (i gr = 10 m a) v rgm 10 12.5 18 volts peak reverse gate blocking current (v gr = 10 v) i rgm e e 1.2 m a total turn-on time (source voltage = 12 v, r s = 6 k ohms) (i tm = 8.2 a, i gt = 2 ma, rated v drm ) (rise time = 20 ns, pulse width = 10 m s) t gt e 2.0 e m s dynamic characteristics critical rate of rise of offstate voltage (v d = rated v drm , r gk = 1 k w , exponential waveform, t c = 110 c) dv/dt e 10 e v/ m s repetitive critical rate of rise of onstate current (cf = 60 hz, i pk = 30 a, pw = 100 m s, dig/dt = 1 a/ m s) di/dt e e 100 a/ m s (1) case 369a when surface mounted on minimum pad sizes recommended. (2) r gk current not included in measurement.
mcr703a series http://onsemi.com 3 + current + voltage v tm i drm at v drm i h symbol parameter v drm peak repetitive off state forward voltage i drm peak forward blocking current v rrm peak repetitive off state reverse voltage i rrm peak reverse blocking current v tm peak on state voltage i h holding current voltage current characteristic of scr anode + on state reverse blocking region (off state) reverse avalanche region anode forward blocking region i rrm at v rrm (off state) 30 c 60 c 90 c figure 1. average current derating figure 2. onstate power dissipation figure 3. onstate characteristics figure 4. transient thermal response 5.0 0 i t(av) , average onstate current (amps) 110 105 i t(av) , average onstate current (amps) 5.0 0 1.0 0 3.0 4.0 0.5 v t , instantaneous onstate voltage (volts) 100 10 1.0 0.1 t, time (ms) 1.0 0.1 1.0 0.1 0.01 3.5 t c , maximum allowable case temperature ( c) p i r (t) , transient resistance (normalized) 100 95 3.0 1.0 2.0 4.0 4.0 1.0 2.0 3.0 2.0 3.0 4.0 1.0 1.5 2.0 2.5 10 100 1000 10,000 5.0 , average power dissipation (watts) (av) t , instantaneous onstate current (amps) 4.5 z jc(t) = r jc(t) ? r(t) 120 c 180 c dc 30 c 60 c 90 c 120 c 180 c dc maximum @ t j = 110 c maximum @ t j = 25 c typical @ t j = 25 c
mcr703a series http://onsemi.com 4 110 40 t j , junction temperature ( c) 2.0 1.5 i h , holding current (ma) i 0.5 0 20 20 0 40 , latching current (ma) l 1.0 60 80 100 110 40 t j , junction temperature ( c) 2.0 1.5 0.5 0 20 20 0 40 1.0 60 80 100 t j , junction temperature ( c) 1.0 0 0.5 v gt , gate trigger voltage (volts) 20 40 40 0 20 100 60 80 110 figure 5. typical gate trigger current versus junction temperature 20 40 40 t j , junction temperature ( c) 35 30 25 20 15 0 , gate trigger current ( a) i gt 20 100 60 80 110 figure 6. typical gate trigger voltage versus junction temperature figure 7. typical holding current versus junction temperature figure 8. typical latching current versus junction temperature
mcr703a series http://onsemi.com 5 minimum recommended footprint for surface mounted applications surface mount board layout is a critical portion of the total design. the footprint for the semiconductor packages must be the correct size to insure proper solder connection interface between the board and the package. with the correct pad geometry, the packages will self align when subjected to a solder reflow process. dpak 0.190 4.826 0.100 2.54 0.063 1.6 0.165 4.191 0.118 3.0 0.243 6.172 mm inches
mcr703a series http://onsemi.com 6 package dimensions dpak case 369a13 issue z d a k b r v s f l g 2 pl m 0.13 (0.005) t e c u j h t seating plane z dim min max min max millimeters inches a 0.235 0.250 5.97 6.35 b 0.250 0.265 6.35 6.73 c 0.086 0.094 2.19 2.38 d 0.027 0.035 0.69 0.88 e 0.033 0.040 0.84 1.01 f 0.037 0.047 0.94 1.19 g 0.180 bsc 4.58 bsc h 0.034 0.040 0.87 1.01 j 0.018 0.023 0.46 0.58 k 0.102 0.114 2.60 2.89 l 0.090 bsc 2.29 bsc r 0.175 0.215 4.45 5.46 s 0.020 0.050 0.51 1.27 u 0.020 0.51 v 0.030 0.050 0.77 1.27 z 0.138 3.51 notes: 1. dimensioning and tolerancing per ansi y14.5m, 1982. 2. controlling dimension: inch. 123 4 style 5: pin 1. gate 2. anode 3. cathode 4. anode
mcr703a series http://onsemi.com 7 notes
mcr703a series http://onsemi.com 8 on semiconductor and are trademarks of semiconductor components industries, llc (scillc). scillc reserves the right to make changes without further notice to any products herein. scillc makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does scillc assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. atypicalo parameters which may be provided in scill c data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. all operating parameters, including atypicalso must be validated for each customer application by customer's technical experts. scillc does not convey any license under its patent r ights nor the rights of others. scillc products are not designed, intended, or authorized for use as components in systems intended for surgical implant into t he body, or other applications intended to support or sustain life, or for any other application in which the failure of the scillc product could create a sit uation where personal injury or death may occur. should buyer purchase or use scillc products for any such unintended or unauthorized application, buyer shall indemnify and hold scillc and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that scillc was negligent regarding the design or manufacture of the part. scillc is an equal opportunity/affirmative action employer. publication ordering information central/south america: spanish phone : 3033087143 (monfri 8:00am to 5:00pm mst) email : onlitspanish@hibbertco.com asia/pacific : ldc for on semiconductor asia support phone : 3036752121 (tuefri 9:00am to 1:00pm, hong kong time) toll free from hong kong & singapore: 00180044223781 email : onlitasia@hibbertco.com japan : on semiconductor, japan customer focus center 4321 nishigotanda, shinagawaku, tokyo, japan 1410031 phone : 81357402745 email : r14525@onsemi.com on semiconductor website : http://onsemi.com for additional information, please contact your local sales representative. mcr703a/d north america literature fulfillment : literature distribution center for on semiconductor p.o. box 5163, denver, colorado 80217 usa phone : 3036752175 or 8003443860 toll free usa/canada fax : 3036752176 or 8003443867 toll free usa/canada email : onlit@hibbertco.com fax response line: 3036752167 or 8003443810 toll free usa/canada n. american technical support : 8002829855 toll free usa/canada europe: ldc for on semiconductor european support german phone : (+1) 3033087140 (mf 1:00pm to 5:00pm munich time) email : onlitgerman@hibbertco.com french phone : (+1) 3033087141 (mf 1:00pm to 5:00pm toulouse time) email : onlitfrench@hibbertco.com english phone : (+1) 3033087142 (mf 12:00pm to 5:00pm uk time) email : onlit@hibbertco.com european tollfree access*: 0080044223781 *available from germany, france, italy, england, ireland
|
